Cranksets

The Wheels Manufacturing BBright Press Fit Bottom Bracket Adaptor for GXP Cranks adapts 24/22mm cranks (SRAM, Truvativ, etc.) to most BBRight frames. Compatible with 2011-2012 Cervelo models R3, R3 Team, S5, S5 Team, S5 VWD, R5ca and R5 VWD. - Includes eight 0.7mm shims for fine-tuning chain line - Machined engineering-grade Delrin - 8g/pr

• Singlespeed crankset • Alloy crankarms w/ solid steel chainring • Square taper interface • Does not include BB

- AL6061-T6 crank with steel chainrings - 7/8sp compatible - 177mm Q-factor - 48.5mm chainline - Spindle Type: 120 SQR JIS

• Square taper interface • Only includes left crank

• Square taper interface • Only includes left crank • 175mm length

- Horizontal square interface - Only includes left crank

• One-piece • 170mm • 24 TPI

The Stages Power meter is built on to a non-drive FC-6800 crank arm specifically to pair with Shimano's Ultegra 6800 crank. The new Stages Power meter is slimmer, and up to 28% lower profile than the original meter. It's sleeker by way of a 17% reduction in frontal area, and they've also made it stronger. The new housing design increases the strength of the battery door and housing connection by 200% over the previous design. This Shimano Ultegra 6800 Stages Power meter is compatible with all Shimano Hollowtech II road drivetrains. - Accuracy: ± 2% - Power meter housing: new low profile design, with new door interface - Weight: Only adds 20g to base crank arm - Battery Life: 200+ hours (coin cell: CR2032) - Power range (Watts): 0 to 2500 - Cadence range (rpm): 20-220 - Water resistance rating: IPX7 - Frame Compatibility: Most frames, see fit guide in the Support section - Device Compatibility: ANT+, Bluetooth Smart Ready Software - Compatibility: Training Peaks, Strava, Garmin Training Center and others

- Optimum Power Transfer - Best Balance For Lighter Weight (-7G) And Efficiency - New Designed Crank Arm - Maintains High Rigidity And Reduces Weight - Hollowglide - 4-Arm Construction Crankset - Adapted For Race Specific Disc Brake System - Shorter Length Of Rear Center With O.L.D. 135mm - Redesign The Gear Teeth Profile To Fit Wider Gear Pitch - 50-34T/53-39T/54-42T/55-42T/52-36T - Iconic Design - Chain Line: 43.5

- Special MTB gear teeth profile improves chain engagement and retention - Stiff and lightweight hollow forged crank maximizes power transfer while limiting weight - Chainline: 52mm - Bottom bracket compatibility: Hollowtech II

- Series: SLX - Crank Construction: HOLLOWTECH II Technology

- Series: SORA - Crank Construction: 2-piece crank construction - Bottom Bracket: BB-RS500, BB-RS500-PB - Chain Line: 43.5 - 9-speed - Four-arm BCD

Shimano Ultegra R8000 crankset. - Optimized lightweight crank arm design produces excellent power transfer efficiency - Minimized weight without sacrificing stiffness - Hollowtech II - Rider tuned gear performance through various gear combinations - Possible to choose the best choice for ride - Redesigned FC for greater frame compatibility - Wider gear pitch increases clearance between chain and leading teeth to provide compatibility with frames with O.L.D. 135mm and 410mm chain stay length - Model Number : FC-R8000 - Series: Ultegra - Crank Construction: Hollowtech II - Crank Arm Length : 165, 170, 172.5, 175mm - Bottom Bracket : SM-BBR60/SM-BBR60-PB - Chain Line: 43.5 - Average Weight: 690 grams (53-39T), 681 grams (52-36T), 674 grams (50-34T), 668 grams (46-36T)

Shimano Chainring Bolts - For use with M9000 chainrings

• 6061-T6 aluminum construction • Adapts 110 or 130 bcd 5-bolt chainrings to fit one-piece or three-piece single bolt cranks • Anodized finish • Made in the U.S.A.

Revamp the look of your single speed cranks with some new hardware. Origin-8's Single Chainring Bolts give a high polished look to any crankset. The anodized finish comes in multiple colors to highlight your crank and makes it look as good as you do. You can also choose between steel or aluminum bolts. • Set of 5 male/female bolts • Inside measures 4mm when tightened, 7mm total height

Wolf Tooth designed these bolts to be the best on the market. These optimized single chainring bolts have a 4mm hex socket on the bolt and a 6mm hex socket on the nut...that's right, no more spanner for your single ring bolts! These are 6mm long so they work perfectly with any bolt on single chainring that does not have threaded standoffs. - 6mm length - Made in the US out of 7075 Aluminum Alloy - Has hex heads on both the bolt and nut for easy installation - Max torque of 6-7 Nm with light grease on threads only

The Wheels Manufacturing 386 EVO Adapter for 22/24mm Spindle Cranks adapts SRAM/Truvativ cranks to 386EVO-standard frames. Simply tap the adapters into the 6806 bearing in the BB shell or cups, then install the cranks using the included spacers to adjust chainline or to take up any side-to-side movement in the crank. - Machined engineering-grade Delrin - 48g/pr Includes - (1) - 24mm ID adapter (for right-side) - (1) - 22mm ID adapter (for left-side) - (8) - 0.7mm spacers

The Wheels Manufacturing 386 EVO Adaptor for Shimano Hollowtech II Cranks adapts Shimano cranks to 386EVO-standard frames. Simply tap the adapters into the 6806 bearing in the BB shell or cups, then install the cranks using the included spacers to adjust chainline, or to take up any side-to-side movement in the crank. - Machined engineering-grade Delrin - 48g/pr Includes - (2) - 24mm ID adapters - (8 )- .7mm spacers

Machined engineering-grade Delrin inserts for adapting bottom brackets to a different type of crankset spindle. - Adapts PF30 and Cannondale BB30-73A bottom brackets for use with SRAM/TruVativ cranksets - Delrin adaptors fit between bearings and crank spindle - BB Shell Width (mm): 68 mm , 73 mm - Spindle Interface Type: TruVativ GXP - BB/Frame Interface: PF30

Machined engineering-grade Delrin inserts for adapting bottom brackets to a different type of crankset spindle. - Adapts PF30 and Cannondale BB30-73A bottom brackets for use with Hollowtech II cranksets - Delrin adaptors fit between bearings and crank spindle - BB Shell Width (mm): 68 mm , 73 mm - Spindle Interface Type: Hollowtech II - BB/Frame Interface: PF30

Wheels Manufacturing BB30 Bottom Bracket Adaptor for GXP Cranks adapts 22/24mm Spindle Cranks (SRAM/TruVativ) to work on BB30 frames. Simply tap the adapters into the 6806 bearing in the BB shell, then install the spindle and cranks. Use Wheels Mfg Crank Spindle Spacers to adjust your chainline, or take up any side-to-side movement in your cranks. These spacers are machined from engineering-grade Delrin.

Wheels Manufacturing BB30 Bottom Bracket Adaptor for Hollowtech II Cranks adapts 24mm Spindle Cranks (Shimano Hollowtech II, FSA, Race Face EXI, etc.) to work on BB30 frames. Simply tap the adapters into the 6806 bearing in the BB shell, then install the spindle and cranks. Use Wheels Mfg Crank Spindle Spacers to adjust your chainline, or take up any side-to-side movement in your cranks. These spacers are machined from engineering-grade Delrin.

- 8 bikes worth of adapters for Shimano 24mm and SRAM/Truvativ 24/22mm cranks to virtually any BB30 or Pressfit 30 frame, including mountain bikes, 2x10 systems, narrow-shell road bikes, road triples, etc. - 65 piece kit includes 4 each Shimano and SRAM adapter sets, plus extra spacers for chainline adjustment and a puller for removing adapters - Includes: (8) Shimano adapter (24mm ID, Shimano right or left; SRAM right only), (4) SRAM-left adapter (22mm ID, Shimano right or left; SRAM right only), (4) SRAM-right adapter (24mm ID, Shimano right or left; SRAM right only), (12) 0.7mm spacer - right (24mm ID, Shimano right or left; SRAM right only), (4) 1.8mm spacer - right (24mm ID, Shimano right or left; SRAM right only), (4) 2.5mm spacer - right (24mm ID, Shimano right or left; SRAM right only), (8) 1.0mm spacer - left (30mm ID, SRAM), (4) 2.5mm spacer - left (30mm ID, SRAM), (4) 5mm spacer - left (30mm ID, SRAM), (4) 10mm spacer - left (30mm ID, SRAM), (8) wave washer, (1) removal tool for pulling adapter out of BB

Wheels Manufacturing BBRIGHT BB30A and PF30A Adaptor for 24mm Spindle Cranks adapts 24mm spindle cranks (Shimano, FSA, etc.) to most BBRight frames. Compatible with 2011-2012 Cervelo models R3, R3 Team, S5, S5 Team, S5 VWD, R5ca and R5 VWD. - Also adapts Cannondale BB30a and PF30a frames to 24mm spindle cranks (Shimano, FSA, etc.). - Includes eight 0.7mm shims for fine-tuning chain line - Machined engineering-grade Delrin - 48g/pr

Use these Wheels Manufacturing Crank Spindle Spacers to adjust chainline or bearing play in bottom brackets. - 24mm for Shimano Hollowtech II, FSA, Race Face EXI, SRAM GPX - 30mm for BB30, PF30, BB86, BB92 and other cranks with 30mm spindles - Machined engineering-grade Delrin - 10 spacers per bag

Wheels Manufacturing Wave Washers help eliminate side play in cranks or pre-loaded angular contact bearings. Please refer to your crankset manufacturer's installation instructions for proper placement. - 24mm for Shimano Hollowtech II, FSA, Race Face EXI, SRAM GPX - 30mm for BB30, PF30, BB86, BB92 and other cranks with 30mm spindles - Uncompressed Thickness: 2.1mm - Compressed Thickness: 0.5mm - Spring Steel - 10 per bag

Machined aluminum spacers for freehubs. Great for fine tuning freewheel and cassette placement or improving chainline. Also good for bottom bracket spacing with BSA BB cups. - Inner Diameter: 35.0mm - Outer Diameter: 40.7mm - Material: Aluminum - Finish: Polished - Bags of 10

Wheels Manufacturing Press Fit 30 Bottom Bracket Adapter for 22/24mm Spindle Cranks adapts 22/24mm Spindle Cranks (SRAM/TruVativ) to work on PF30 frames. Simply tap the adapters into the 6806 bearing in the BB shell, then install the spindle and cranks. Use Wheels Mfg Crank Spindle Spacers to adjust your chainline, or take up any side-to-side movement in your cranks. These spacers are machined from engineering-grade Delrin. Notes: - PF30-SRAM was originally designed for use with SRAM PF30 bottom brackets and will not work with Wheels Manufacturing PF30-BB, PF30-BB-AC or PF30-BB-CER. Use Wheels Mfg BBUNIV-SRAM to adapt 22/24mm Spindle Cranks (SRAM/TruVativ) in Wheels Manufacturing PF30 bottom brackets. - Not compatible with SRAM PF30 bottom brackets that use a thin plastic reducer inserted into the bearings. - The stock bottom bracket seals must be removed before installing the Pressfit 30 adapter

The Wheels Manufacturing PressFit 30 Bottom Bracket Adaptor for Shimano Cranks adapts 24mm Spindle Cranks (Shimano Hollowtech II, FSA, Race Face EXI, etc.) to work on PF30 frames. Simply tap the adapters into the 6806 bearing in the BB shell, then install the spindle and cranks. Use Wheels Mfg Crank Spindle Spacers to adjust your chainline, or take up any side-to-side movement in your cranks. These spacers are machined from engineering-grade Delrin. Notes: - PF30-SHIM was originally designed for use with SRAM PF30 bottom brackets and will not work with Wheels Manufacturing PF30-BB, PF30-BB-AC or PF30-BB-CER. Use Wheels Mfg BBUNIV-SHIM to adapt 24mm Spindle Cranks (Shimano, FSA, etc.) in Wheels Manufacturing PF30 bottom brackets. - Not compatible with SRAM PF30 bottom brackets that use a thin plastic reducer inserted into the bearings. - The stock bottom bracket seals must be removed before installing the Pressfit 30 adapter